Search Results

Collective life-cycle data is needed when developing components like elastomer suspension mounts. Life-time prediction is only possible using thermal load frequency distributions. In addition to current extreme load cases, the Idle Load Case is examined at Mercedes-Benz Car Group as a collective load case for Vehicle Thermal Management (VTM) numerical simulations in early development stages. It combines validation opportunities for HVAC, cooling and transmission requirements in hot-country-type ambient conditions. Experiments in climatic wind tunnels and coupled 3D CFD and heat transfer simulations of the Idle Load Case have been performed. Measurements show steady conditions at the end of the load case. Decoupling of the torque converter, changes in ambient temperature and the technical implementation of a wind barrier for still air conditions exhibit influence on component-level results. Solar load, however, does not significantly change the examined component temperatures.

An accurate model to predict the formation of fogging and defogging which occurs for low windshield temperatures is helpful for designing the air-conditioning system in a car. Using a multiphase flow approach and additional user-defined functions within the commercial CFD-software STAR-CCM+, a model which is able to calculate the amount of water droplets on the windshield from condensation and which causes the fogging is set up. Different parameters like relative humidity, air temperature, mass flow rate and droplet distributions are considered. Because of the condition of the windshield's surface, the condensation occurs as tiny droplets with different sizes. The distribution of these very small droplets must be obtained to estimate numerically the heat transfer coefficient during the condensation process to predict the defogging time.

The geometric shape of the tires can have a large influence on the aerodynamic drag of a passenger car as it has been shown already in different publications like for example [1, 2, 3]. However, to optimize the shape of a tire, nowadays quite some effort is needed in terms of wind tunnel time and costs for prototype tires. In this paper an approach to optimize the tire's shape in model scale is described, which can help to reduce both development time and costs. The first step in the development of this method was to verify that the aerodynamic effects of the tire geometry in model scale are comparable to full scale tests. This was achieved by measuring different production tires in full scale and also by measuring the quarter scale version of the same tires. The only difference between the original and the model scale tires was that the scaled tires were not deformable. The results show that the difference between two sets of tires is comparable in full scale and in quarter scale.

The increasing importance of electric mobility results into the need for optimizing all power train components to further reduce the energy consumption of the vehicle. The aim of this study is to predict the thermal behavior and the pressure losses in water jackets of electric machines by use of CFD. The heat loss of electric machines in passenger cars is sufficient to let its components reach critical temperatures. For this reason, the optimization of heat dissipation plays an important role. The goal of efficient heat dissipation is a high heat transfer coefficient. At the same time, the pressure loss should be low in order to reduce the required power of the pump. Flow simulations can help to evaluate different water jacket concepts in an early stage of development. In this work, the validation of flow simulations in water jackets is based on measurements of a simplified geometry with constant boundary conditions.

In the digital prototype development process of a new Mercedes-Benz, thermal protection is an important task that has to be fulfilled. In the early stages of development, numerical methods are used to detect thermal hotspots in order to protect temperature sensitive parts. These methods involve transient full Vehicle Thermal Management (VTM) simulations to predict dynamic vehicle heat-up during critical load cases. In order to simulate thermal control mechanisms, a coupled 1D to 3D thermal vehicle model is built in which the coolant and oil circuit of the engine, as well as the exhaust flow are captured in detail. When performing a transient 3D VTM analysis, the conduction and radiation phenomena are simulated using a transient structure model while the convective phenomena are co-simulated in a steady state fluid model. Both models are brought to interaction at predetermined points by an automatized coupling method.

In this paper a new numerical methodology to compute component temperatures of a rotating cardan shaft is described. In general temperatures of the cardan shaft are mainly dominated by radiation from the exhaust gas system and air temperatures in the transmission tunnel and underbody. While driving the cardan shaft is rotating. This yields a uniform temperature distribution of the circumference of the shaft. However most simulation approaches for heat protection are nowadays steady-state computations. In these simulations the rotation of the cardan shaft is not considered. In particular next to the exhaust gas system the distribution of the temperatures of the cardan shaft is not uniform but shows hot temperatures due to radiation at the side facing the exhaust gas system and lower temperatures at the other side. This paper describes a new computational approach that is averaging the radiative and convective heat fluxes circumferentially over bands of the cardan shaft.

In this paper the latest status of the Vehicle Thermal Management (VTM) simulation at the Mercedes-Benz Car Group is shown. First of all VTM is nowadays a routine simulation application and secondly it is embedded in a standard process which starts with the CAD data collection and ends with standard reporting of the simulation results and thirdly VTM is now an integrated simulation application in terms of VTM includes the classical underhood-underbody analysis, the analysis of electric/electronic components, the brake temperature analysis and last not least the thermal comfort of passengers. There is also a close link to the tests of vehicle hardware. Beside the operational simulation process there is a process installed which guarantees good quality of the results.

The combination of enhanced powertrains and adapted vehicle concepts can reduce the energy demand of vehicles significantly, especially when energy conversion efficiency rises and at the same time driving resistances decrease. In addition, new powertrain concepts are able to offer extra functionality due to a growing cross-linking with chassis and vehicle body. The design of highly linked vehicles and powertrain systems requires additional new development methods in order to answer interacting questions of driving dynamics and vehicle energy efficiency at an early stage of development. In the paper a database-based simulation platform is presented which was developed at the IVK of the University of Stuttgart in cooperation with the Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS). The simulation platform is used as an example to discuss mass reducing developments for various powertrain concepts.

Wind noise has become an important indicator for passenger automobile quality. Several transmission paths can be related to different parts of the vehicle exterior. While the greenhouse (side glasses, windshield, seals & others) often dominates the interior noise level above 500 Hz, the contribution coming from the underbody area usually dominates the interior noise spectrum at lower frequencies. This paper describes a framework of numerical tools which is capable of determining realistic underbody turbulent and acoustic loads being generated for typical driving conditions, as well as performing the noise transmission through underbody panels and the propagation of sound to the drivers ear location.

In this paper the effect of aerodynamic modifications that influence the unsteady aerodynamic properties of a vehicle on the response of the closed loop system driver-vehicle under side wind conditions is investigated. In today's aerodynamic optimization the side wind sensitivity of a vehicle is determined from steady state values measured in the wind tunnel. There, the vehicle is rotated with respect to the wind tunnel flow to create an angle of attack. In this approach however, the gustiness that is inherent in natural wind is not reproduced. Further, unsteady forces and moments acting on the vehicle are not measured due to the limited dynamic response of the commonly used wind tunnel balances. Therefore, a new method is introduced, overcoming the shortcomings of the current steady state approach. The method consists of the reproduction of the properties of natural stochastic crosswind that are essential for the determination of the side wind sensitivity of a vehicle.

This paper presents an integrated numerical and experimental approach to take best possible advantage of the common development tools at hand (1D, CFD and wind tunnel) to determine the cooling air mass flow at the different vehicle development stages. 1D tools can be used early in development when neither 3D data nor wind tunnel models with detailed underhood flow are available. A problem that has to be resolved is the dependency on input data. In particular, the pressure coefficients on the outer surface (i.e. at the air inlet and outlet region) and the pressure loss data of single components are of great importance since the amount of cooling air flow is directly linked to these variables. The pressure coefficients at the air inlet and outlet are not only a function of vehicle configuration but also of driving velocity and fan operation. Both, static and total pressure coefficient, yield different advantages and disadvantages and can therefore both be used as boundary conditions.

Previous work by the authors showed the development of an aerodynamic CFD model using the Lattice Boltzmann Method for simulating vehicles inside the IVK Model-Scale Wind-Tunnel test-section. In both experiment and simulation, alternate configurations of the wind-tunnel geometry were studied to change the pressure distribution in the wind-tunnel test section, inducing a reduction in aerodynamic drag due to interference between the wind-tunnel geometry and the pressure on the surface of the vehicle. The wind-tunnel pressure distribution was modified by adding so-called “stagnation bodies” inside the collector to create blockage and to increase the pressure in the rear portion of the test section. The primary purpose of previous work was to provide a validated CFD approach for modeling wind-tunnel interference effects, so that these effects can be understood and accounted for when designing vehicles.

In this study the numerical simulation of the flow through an alternator inside an engine compartment of a passenger car is investigated. Specifically the interaction of the flow through the alternator with the flow through the engine compartment is explored in detail. The results are compared with a corresponding numerical simulation of an alternator in a surrounding of a test facility and with a numerical simulation of the flow through an engine compartment without taking into account the internal flow through the alternator. Finally the air temperature near the alternator and also the temperature of some components inside the alternator are compared with experimental values measured during a typical load case used for the thermal protection of the passenger car.

The unsteady environment road vehicles are exposed to is subject of many investigations that are currently made. Yet, the approaching flow is only one aspect of unsteady forces acting on the vehicle. Unsteady wake structures also lead to time-varying surface pressures and consequently fluctuating forces even in steady and low turbulent flows. However, little is known about the influence of realistic flow conditions, i.e. as found on road, on the unsteady surface pressures and wake structures of a vehicle. Therefore, to derive a deeper understanding of the unsteady aerodynamic properties of a vehicle this paper presents results of measurements conducted on a vehicle body both in smooth and turbulent flow conditions in the IVK model scale wind tunnel. Unsteady surface pressure measurements in the area where separation occurs and the base of the vehicle were made together with time accurate total pressure measurements in the wake.

Recently built or refurbished wind tunnel facilities show a trend towards a detailed simulation of road conditions. Therefore, these wind tunnel facilities are equipped with boundary layer conditioning systems and a rolling road consisting of one or several belts in order to simulate the rotation of the wheels and the relative motion between the vehicle underfloor and the road. Belts are either realized in rubber or steel. Steel belts offer the possibility to be coated with rubber to protect the belt itself. This coating additionally offers the possibility to attain a certain roughness to represent the road surface. This paper presents measurements of the roughness of the steel belt systems installed in the IVK Model Scale and Aero-Acoustic Full Scale Wind Tunnel in comparison to road surfaces. Additionally, the influence of roughness on the aerodynamic coefficients drag and lift is presented and discussed for the SAE reference body with different rear end configurations.

This paper summarizes a common project of Mercedes-Benz and FKFS (Research Institute of Automotive Engineering) to apply numerical methods to thermal soak issues in a very early stage of the development phase of a new car. “Thermal soak” results from driving the vehicle at high load followed by shutting off the engine and a cool down phase. After stopping, the underhood flow is only driven by natural convection. The thermal soak behaviour is discussed in principal and the numerical challenges are summarized. Four different issues are identified: the need for a transient computation including transient thermal load pattern, a method to compute natural convection in the underhood after the shutdown of the engine, the complex geometry and the lack of a single computational program to consider all three modes of heat transfer, which results in a coupled numerical approach.

Aerodynamic simulations using CFD is now a standard tool in the automotive industry, and is becoming more and more integrated in the aerodynamic design process of new vehicles. This process is distinguished by parallel development with wind tunnel experiments and CFD simulation results, which demands comparable results to be generated by the two development tools. As wind tunnel effects are not simulated in most industrial applications of CFD, the comparison with experimental results normally show differences partly due to wind tunnel effects and ground simulation effects. Therefore a deeper understanding of wind tunnel effects and methods to fully reproduce experimental values with CFD is necessary. In this paper, an extensive validation study with a detailed scale notchback model inside an open jet wind tunnel is presented. This study includes experimental data from the real wind tunnel as well as CFD simulation results with and without wind tunnel effects.

This paper presents some recent results concerning the generation and minimization of cooling air drag, achieved in an integrated approach of numerical and experimental investigations. The baseline configuration of a production cars' cooling air flow system is analyzed. The analysis of the created drag shows, that most of the force changes due to the cooling air flow appear in the front region of the vehicle. However, the forces generated by heat exchangers are only a small share of the total changes. Additional drag is generated for example by the front wheels and by the components of the underhood compartment. The investigation of the influence of the vehicle rear end shape on the aerodynamics of the cooling air flow system shows, that two similar cars with different rear end shapes (notchback and squareback) can feature different cooling air drag values.

Wind tunnel interference effects are still considered to be negligible - or at least undesired - in automotive aerodynamics. Consequently, up to now there is no standard correction method which is used in everyday wind tunnel testing although a lot of research has been done in recent years. In most full-vehicle CFD simulations, wind tunnel interference effects are not simulated. The flow about the car is computed under idealized conditions. The wind tunnel is designed to simulate these conditions but fails to do so to some degree due to its limited size. Therefore a comparison of blockage-free CFD results and wind tunnel measurements is deficient. Hence CFD simulations including wind tunnel interference effects should be favored in the future for validation purposes. Furthermore, CFD offers new possibilities to investigate individual contributions to wind tunnel interference effects and therefore could help to increase the understanding of the flow in the wind tunnel.

This paper describes a method to simulate underhood temperature distributions in passenger cars. A simplified engine compartment simulation test rig is used to perform measurements with well known boundary conditions to validate the simulation strategy. The measurement setup corresponds to idle without working fan. The aim of this setup is to validate cases with strong natural convection, e.g. thermal soaking. A coupled steady-state CFD run and thermal analysis is undertaken to simulate the temperature distribution in the test rig. Convective heat transfer coefficients and air temperatures are calculated in StarCD™. The radiative and conductive heat transfer is considered in a RadTherm™ analysis. The strong coupling of flow field and wall temperature in buoyancy driven flows requires an iterative process. Calculated temperatures are compared to measured results in order to validate the simulation method as far as possible. Some of the results are reported in this paper.